Filterpatrone für Luftreiniger (2 Stück)

G4 Filter for Coarse Filtration

Aims at relatively bigger particles (≥ 5 μm in diameter). It filters out more than 90% of PM10 and PM5.

F9 Filter for Finer Filtration

Works at particles that measure 1 μm or above in diameter. It filters out more than 95% of PM10, PM5 and PM2.5.

Customized Activated Carbon Filter

A dense pack of activated carbon is also added to absorb VOCs that particulate matter filters can't capture. Unpleasant odor is no longer a problem.

VOCs

Customized Activated Carbon Filter

Two layers of 70 mm-thick HEPA H13 filter as the final stage gate. They are able to trap up to 99.97% of airborne particles of all sizes, including PM0.3 that are known to be the most penetrating particles in the air.

Long Live the Filter Cartridge

Efficiency is not all that matters. The different levels of filter are arranged in certain order inside the cartridge to maximize its lifespan, so that you won't need to replace the cartridge until it gets fully used.

Filter Life Detection

Snapmaker 2.0 carries out a real-time monitoring on the Filter Cartridge and shows its lifespan on the Touchscreen. It lets you know when it's time to pop in a new one.

Easy to Replace

With all the filters integrated into a single cartridge, replacement is as simple as taking the old one out, and putting a new one in.

Specifications

In the Box

Filter Cartridge x 2

[1] Using the Air Purifier when printing with ABS or other thermo-sensitive filaments may lead to poor printing quality. If you need to filter 3D printing emissions, it's recommended to turn on the Air Purifier after printing job is finished.

[2] The data is sourced from the Snapmaker Testing Laboratory. Experimental Conditions: With the enclosure and the enclosure fan in use, the 1.6W, 10W, 20W, and 40W laser modules were employed to continuously cut 2mm, 3mm, 5mm, and 5mm basswood sheets for 5 minutes respectively, to measure the PM and TVOC content at the outlet of the exhaust duct. Due to variations in usage conditions and environments, the specific performance and results in actual use may differ from the provided data. Snapmaker shall not be held responsible for any discrepancies or consequences resulting from such environmental changes.

[3] The Touchscreen UI is subject to change due to iterations.

[4] This data is obtained under the condition of typical laser use, and is for reference only.

The Exact Filter Cartridge You Need

Tailor-made filter cartridge for your Snapmaker 2.0, with five layers of different filters consolidated into one, it is designed to absorb what's actually emitted during laser engraving or 3D printing process^[1].

G4 Filter for Coarse Filtration

Aims at relatively bigger particles (≥ 5 μm in diameter). It filters out more than 90% of PM10 and PM5.

F9 Filter for Finer Filtration

Works at particles that measure 1 μm or above in diameter. It filters out more than 95% of PM10, PM5 and PM2.5.

Customized Activated Carbon Filter

A dense pack of activated carbon is also added to absorb VOCs that particulate matter filters can't capture. Unpleasant odor is no longer a problem.

Ultra-dense HEPA H13 Filter

Two layers of 70 mm-thick HEPA H13 filter as the final stage gate. They are able to trap up to 99.97% of airborne particles of all sizes, including PM0.3 that are known to be the most penetrating particles in the air.

Long Live the Filter Cartridge

Efficiency is not all that matters. The different levels of filter are arranged in certain order inside the cartridge to maximize its lifespan, so that you won't need to replace the cartridge until it gets fully used.

Filter Life Detection

Snapmaker 2.0 carries out a real-time monitoring on the Filter Cartridge and shows its lifespan on the Touchscreen. It lets you know when it's time to pop in a new one.

Easy to Replace

With all the filters integrated into a single cartridge, replacement is as simple as taking the old one out, and putting a new one in.

Specifications

In the Box

Filter Cartridge x 2

[1] Using the Air Purifier when printing with ABS or other thermo-sensitive filaments may lead to poor printing quality. If you need to filter 3D printing emissions, it's recommended to turn on the Air Purifier after printing job is finished.

[2] The data is sourced from the Snapmaker Testing Laboratory. Experimental Conditions: With the enclosure and the enclosure fan in use, the 1.6W, 10W, 20W, and 40W laser modules were employed to continuously cut 2mm, 3mm, 5mm, and 5mm basswood sheets for 5 minutes respectively, to measure the PM and TVOC content at the outlet of the exhaust duct. Due to variations in usage conditions and environments, the specific performance and results in actual use may differ from the provided data. Snapmaker shall not be held responsible for any discrepancies or consequences resulting from such environmental changes.

[3] The Touchscreen UI is subject to change due to iterations.

[4] This data is obtained under the condition of typical laser use, and is for reference only.