Name: Support for PLA Filament (RFID) - 500g
Brand: Snapmaker
SKU: 34342
Price: 22.99 EUR
Availability: InStock

Support for PLA Filament (RFID) - 500g

Snapmaker Support for PLA

We recommend using Support for PLA Filament for the support interface and PLA for the support base.

Peel Away, Remove with Ease

Designed for PLA prints, Snapmaker Support for PLA reduces bonding between the support interface and the model. Remove supports with less reliance on tools, spend less time on post-processing, and keep more of the fun in creating.

Stable Interface, Cleaner Prints

During printing, Snapmaker Support for PLA stays securely bonded to the PLA support body, helping prevent loose material from being carried onto the model by the nozzle. Fewer color streaks. A cleaner finish.

Close Support, Smooth Curves

With support interface settings in Snapmaker Orca, the interface sits close beneath curved overhangs, giving each layer steady support. It helps reduce sagging and rough layer lines, leaving underside curves smooth and even.

Less stress, More Detail

When removing supports the material separates cleanly from the model, minimizing stress on delicate features. Even the finest structures in miniature models can be freed from their supports with confidence, keeping every detail intact.

RFID-Erkennung^[1]

When used with the Snapmaker U1, the printer automatically loads preset filament information for a more convenient printing experience.

Control panel with buttons for audio recognition and modes.

Recycelte Spulen und Verpackungen

Sowohl die Spule als auch die Verpackungsschachtel bestehen aus recycelten Materialien, wodurch der Einsatz von Neuware reduziert wird.

Tipps zum Drucken

Trocknung und Lagerung

• Pre-Drying: Support for PLA Filament has low moisture sensitivity and generally does not require drying. However, pre-drying is recommended for optimal print results. The recommended setting is 50°C for 6 hours.

• Storage: When not in use, we recommend keeping the filament away from direct sunlight in a sealed container with desiccant.

Drucken

• Use Only as a Support Interface: We strongly recommend using Support for PLA Filament only as a support interface material. Do not use it for the entire support body. In “Process,” switch to “Advanced” mode. Then go to “Support > Filament for Supports,” enable support, and set “Support/raft interface” to “Sup.PLA.” Continue using the same PLA as the model for the support body.

• Choose Support Type Based on Model Geometry: For large flat areas, regular overhangs, or structures that need stable support, standard support is recommended. For curved surfaces or other complex geometries, tree support is recommended to reduce contact area and material use. Results may vary by model, so check support coverage in the slicer preview.

• Improve Support Interface Quality: Setting "Top Z distance," "Bottom Z distance," "Top interface spacing," and "Bottom interface spacing" all to 0 mm gives a smoother support interface. To bring supports closer to the model's side walls, slightly reduce "Support/object xy distance" (avoid setting it to 0 mm by default, as overly tight contact can make removal difficult). If some overhangs lack sufficient support, increase the “Threshold angle” in increments of 5–10° while checking the slicer preview. If the interface surface is still uneven, try enabling "Ironing Support Interface."

• Reduce Standby Filament Carbonization: During multi-color printing, filament in the standby toolhead may gradually carbonize due to prolonged heating, affecting extrusion stability. Increase the prime tower’s purge volume and purge line spacing as appropriate to help flush out carbonized filament and improve print reliability.

Technische Daten

Empfohlene Druckbedingungen

* Basierend auf einer 0,4-mm-Düse. Die Druckbedingungen können je nach Düsen-Durchmesser variieren.

Düsentemperatur

200–230°C

Betttemperatur

25–65 °C

Lüfter

EIN

Druckgeschwindigkeit

Bis zu 200 mm/s

Trocknungseinstellungen vor dem Drucken

Dry at 50°C for 6 h

Physikalische Eigenschaften

Dichte

1.296 g/cm³ at 23°C

Schmelzindex

25.944 g/10 min

Glasübergangstemperatur

58.2°C

Vicat-Erweichungstemperatur

65.5°C

Empfohlene Druckbedingungen

*Basierend auf einer 0,4-mm-Düse. Die Druckbedingungen können je nach Düsen-Durchmesser variieren.

Düsentemperatur

200–230°C

Betttemperatur

25–65 °C

Lüfter

EIN

Druckgeschwindigkeit

Bis zu 200 mm/s

Trocknungseinstellungen vor dem Drucken

Dry at 50°C for 6 h

Physikalische Eigenschaften

Dichte

1.296 g/cm³ at 23°C

Schmelzindex

25.944 g/10 min

Glasübergangstemperatur

58.2°C

Vicat-Erweichungstemperatur

65.5°C

Produktressourcen

Symbol, das ein PDF-Dokument mit darüber liegenden Textzeilen darstellt.

Technisches Datenblatt

Benutzerhandbuch

Hexadezimal-Codetabelle

Technisches Datenblatt

Benutzerhandbuch

Hexadezimal-Codetabelle

Im Lieferumfang enthalten

Versiegeltes Spulenfilament × 1

Trockenmittel× 1

Verpackungskarton aus Papier× 1

Versiegeltes Spulenfilament × 1

Verpackungskarton aus Papier × 1

Hinweis:
[1] Die RFID-Funktion ist nur beim Snapmaker U1 verfügbar. Da sich die RFID-Lesegeräte in der Nähe der Spulenhalter auf beiden Seiten des Druckers befinden, können Filamentinformationen nur erfasst werden, wenn die Spule auf einem Halter platziert ist.

Häufig gestellte Fragen

1. Kompatibilität

• Snapmaker U1: Use Snapmaker Support for PLA with Snapmaker Orca by assigning it to the support interface in the slicer settings.

• Other FDM 3D printers: Compatibility depends on the printer and its supported materials. Manual configuration of printing and support settings may be required.

Always check the printer's material compatibility and the recommended setup before printing.

2. Can I use Snapmaker Support for PLA to print the entire support structure?

To save printing time and filament while maintaining print quality, we strongly recommend using Snapmaker Support for PLA only as the support interface material, rather than for the entire support structure. Use regular PLA for the main support structure and Snapmaker Support for PLA for the interface in contact with the model.

3. How do I set up Snapmaker Support for PLA in Snapmaker Orca?

Follow these steps to configure the support interface:

Switch to Advanced mode in the Process settings.
Go to Support and enable supports.
Under Filament for Supports, assign Snapmaker Support for PLA to Support/raft interface.
- Continue using the same PLA as the model for the main support structure.

This configuration allows Snapmaker Support for PLA to be used at the contact interface while regular PLA provides the main support structure.

4. Which support type should I use with Snapmaker Support for PLA?

Choose the support type based on your model's geometry:

Standard support: Recommended for large flat areas, regular overhangs, and structures that require stable support.
Tree support: Recommended for curved surfaces, figurines, and complex geometries where reducing contact area and material consumption is desirable.

Results may vary depending on the model. Check the slicer preview to ensure that all areas requiring support are adequately covered.

5. How can I improve the support interface quality?

When using Snapmaker Support for PLA as the support interface material, you can try the following settings in Snapmaker Orca:

- -Top Z distance: 0 mm
-Bottom Z distance: 0 mm
-Top interface spacing: 0 mm
-Bottom interface spacing: 0 mm

These settings can help improve the smoothness of supported surfaces.

For additional adjustments:

- -Bring supports closer to the model: Slightly reduce Support/object XY distance. Avoid setting it to 0 mm by default, as excessively tight contact may make support removal more difficult.
-Improve support coverage: If some overhangs lack sufficient support, increase the Threshold angle in increments of 5–10° while checking the slicer preview.
-Improve surface smoothness: If the support interface remains uneven, try enabling Ironing Support Interface.

Actual results depend on the model geometry and printing conditions. Adjust settings as needed.

6. What are the recommended printing settings for Snapmaker Support for PLA?

Parameter	Recommended Setting
Düsentemperatur	200–230°C
Betttemperatur	25–65 °C
Lüfter	EIN
Druckgeschwindigkeit	Bis zu 200 mm/s
Drying Before Printing	55°C for 8 hours

These settings are based on testing with a 0.4 mm nozzle. Actual printing conditions may vary depending on the printer, nozzle diameter, model geometry, and other factors.

7. Build Plate Recommendation

Druckplatte	Kompatibilität
Strukturierte PEl-Platte	Kompatibel
Glatte PEI-Platte	Kompatibel
Grafik-Effektplatte	Not Compatible

Hinweis:

If the printed model adheres too strongly to the build plate, allow the plate to cool before attempting removal. Follow the printer's safety instructions and the build plate manufacturer's recommendations. If a suitable release method is needed, ensure the plate is cool and follow the relevant product instructions.
If the first layer does not adhere properly, check the bed leveling and clean the build plate. If the issue persists, apply a suitable glue stick or liquid glue, provided it is compatible with the build plate.

8. Do I need to dry Snapmaker Support for PLA before printing?

Snapmaker Support for PLA has low moisture sensitivity and generally does not require drying before use. However, we recommend pre-drying the filament for optimal print quality. The recommended drying settings are 50°C for 6 hours.

9. How should I store Snapmaker Support for PLA?

Store the filament in a sealed, dry environment away from direct sunlight. We recommend keeping it in a sealed container with desiccant when not in use to help protect it from moisture and maintain consistent printing performance.

10. Does Snapmaker Support for PLA support RFID recognition?

Yes. RFID recognition is supported when Snapmaker Support for PLA is used with the Snapmaker U1.

The U1 can automatically detect the filament information and load the corresponding preset settings for a more convenient printing experience.

Note: The RFID readers are located near the spool holders on both sides of the U1. The filament spool must be placed on a spool holder for its information to be detected. RFID recognition is currently available only on the Snapmaker U1.

Bleiben Sie auf dem Laufenden!

Support for PLA Filament (RFID) - 500g

Empfohlenes RFID-Filament

Empfohlenes RFID-Filament

PLA Glow Filament (RFID) - 1kg

PETG-CF-Filament (RFID) – 1 kg

PLA-Filament, durchscheinend (RFID) – 1 kg

PETG-Filament, durchscheinend (RFID) – 1 kg

PETG-HF-Filament (RFID) – 1 kg

PLA-CF-Filament (RFID) – 1 kg

SnapSpeed PLA-Filament (RFID) – 1 kg

Mattes PLA-Filament (RFID) – 1 kg

Zweifarbiges PLA-Filament aus Seide (RFID) – 1 kg

Seiden-PLA-Filament (RFID) – 1 kg

TPU 95A HF-Filament (RFID) – 1 kg

Holz-PLA-Filament (RFID) – 1 kg

Snapmaker Support for PLA

Peel Away, Remove with Ease

Stable Interface, Cleaner Prints

Close Support, Smooth Curves

Less stress, More Detail

RFID-Erkennung[1]

Recycelte Spulen und Verpackungen

Tipps zum Drucken

Technische Daten

Produktressourcen

Im Lieferumfang enthalten

1. Kompatibilität

2. Can I use Snapmaker Support for PLA to print the entire support structure?

3. How do I set up Snapmaker Support for PLA in Snapmaker Orca?

4. Which support type should I use with Snapmaker Support for PLA?

5. How can I improve the support interface quality?

6. What are the recommended printing settings for Snapmaker Support for PLA?

7. Build Plate Recommendation

8. Do I need to dry Snapmaker Support for PLA before printing?

9. How should I store Snapmaker Support for PLA?

10. Does Snapmaker Support for PLA support RFID recognition?

Support for PLA Filament (RFID) - 500g

RFID-Erkennung^[1]